Low-carbon A312 pipe for welded process lines and shop fabrication
We supply TP304L stainless steel pipe for fabricators and industrial distributors. Seamless and welded A312 pipe are quoted separately, with the wall series, end preparation and surface condition kept on each line. Low-carbon material identity stays traceable through full lengths and cut pieces.
| Material | Low-carbon austenitic stainless steel, TP304L |
|---|---|
| Carbon maximum — A312 reference | 0.035% by mass for TP304L |
| Product form | Industrial round pipe; seamless or welded route named on the order |
| Dimensional basis | ASME B36.19 stainless pipe series |
| End preparation | Plain ends, bevels or cut pieces to the fabrication detail |
| Surface | Pickled/mill surface or separately specified mechanical finish |
| Identification | Grade, heat identity and purchased pipe dimensions retained with material records |
Compare the wall at the same NPS before selecting fittings or a weld preparation.
| NPS (in.) | Outside diameter (mm) | 10S nominal wall (mm) | 40S nominal wall (mm) |
|---|---|---|---|
| 1/2 | 21.3 | 2.11 | 2.77 |
| 1 | 33.4 | 2.77 | 3.38 |
| 2 | 60.3 | 2.77 | 3.91 |
| 3 | 88.9 | 3.05 | 5.49 |
| 4 | 114.3 | 3.05 | 6.02 |
| 6 | 168.3 | 3.40 | 7.11 |
| 8 | 219.1 | 3.76 | 8.18 |
No matching specification. Clear the search to see every row.
Scroll sideways to see every column.
Selected ASME B36.19 nominal dimensions for stainless pipe. Our quotation identifies the TP304L route, size, wall and length being supplied. Schedule identifies the wall series; allowable pressure follows the governing piping design and service conditions.
ASTM A312 covers austenitic stainless pipe, including seamless and permitted welded routes. We state the manufacturing route alongside TP304L on the material line so the offered product matches the specified construction.
Lower carbon reduces the tendency to form chromium carbides during a welding thermal cycle. The fabrication procedure sets heat input and welding controls, followed by the required cleaning and weld acceptance.
Dual 304/304L certification requires the material to meet both grades and the certificate to state that designation. We carry the actual certificate designation into the offer and heat-linked release records.
A square plain end suits work where the shop will prepare the joint. Finished cut length and the required cutting tolerance stay separate from the nominal pipe size.
The bevel angle, land and inside alignment follow the connection detail. A heavier wall changes weld preparation and bore alignment even when both pipes have the same NPS.
Pickling chemically removes scale and heat tint; mechanical polishing produces the specified surface texture. An order requiring internal roughness or hygienic acceptance identifies the bore finish, measurement basis and product specification separately from the outside appearance.
Dedicated contact surfaces and clean end protection reduce iron contamination during processing and packing. Carbon-steel grinding dust or dirty straps can spoil a clean stainless surface before installation.
A spool material list can combine different NPS and walls under one grade. Matching the pipe line to its fitting wall and weld detail helps the fabricator plan fit-up without changing the material specification.
Distributors can order size-separated full lengths and cut pieces together. The packing list preserves grade, route and heat identity so partial bundles remain identifiable when material is resold.
XRF helps check the alloying elements. TP304L carbon acceptance uses the material certificate and any carbon-capable analysis required by the order, keeping the low-carbon requirement linked to the supplied heat.
Dimensional checks use the ordered NPS and wall series. Bore alignment is also relevant where a cut piece will be welded to a thicker or thinner fitting.
The applicable A312 testing and any supplementary examinations belong to the selected manufacturing route and purchase specification. Required reports are identified before release.
The inspection scope distinguishes mechanical scratches, contamination and residual heat tint from a requested polished finish. Any measured internal roughness must be tied to an explicit finish requirement.
Clean spacers and protected ends keep the bores clear and reduce contact damage. Different grades are bundled and identified separately so a receiving team can distinguish similar-looking stainless material.
A cut order identifies the finished piece count and length. The quotation itemizes cutting, remnants and additional processing alongside the pipe quantity and agreed price basis.
Our quote identifies TP304L, manufacturing route, dimensions, supplied length, finish and documents. Processing and destination terms remain visible beside the pipe supply.
Supply against a TP304L order requires material records confirming TP304L compliance, including the lower carbon limit. The accepted certificate designation stays with the heat and delivered pieces.
Austenitic 304L has low magnetic response in the annealed condition. Cold work and welding can introduce a magnetic response. Grade acceptance uses the material records, while a project magnetic limit has its own test condition and acceptance criterion.
Schedule 10S and 40S identify their respective wall dimensions. The governing piping design establishes allowable pressure using temperature, material, joint factors and corrosion allowance for the selected wall.
Yes. The cut list identifies finished lengths and quantities; the weld detail identifies bevel, land and any bore-matching requirement. Those operations are itemized with the pipe selection.
Pickled pipe has received a chemical treatment to remove scale and heat tint. Polished sanitary tubing is purchased to its required tube dimensions, surface finish, internal roughness and connection system. We retain the specified product and finish on the order.
They can be identified as separate heat lots. A single-heat requirement must be stated before supply is arranged, and cut pieces need the same traceability discipline as full lengths.
Other items in the same product category.
We wrote these for buyers specifying and receiving exactly this kind of package.
Send the TP304L material list with NPS, Schedule or wall, route, finished lengths and quantity. Include the surface and weld-end detail, required records and destination. Our offer separates pipe supply from cutting, beveling and finish work.